Peugeot 208 Key Replacement
It is better to leave the replacement of Peugeot 208 keys to auto locksmiths who have the necessary equipment and technical know-how. They can create and program keys faster and less expensive than dealers.
If the key fob stopped locking or unlocking your doors, it is likely due to a dead battery in the coin. However, there are other reasons that the key may be malfunctioning.
Dead Coin Battery
A dead coin battery will hinder your Peugeot 208 from locking or unlocking and cannot start the engine. In this instance you'll need to choose the alternate method to start as described in your vehicle's owner's manual.
Another reason your 208 might not start is that the spark plugs are been worn down. The spark plugs are responsible for instigating the fuel that powers the engine. However they have a finite lifespan. They will eventually break down if they aren't used frequently enough.
Luckily, there's an easy solution for this problem. The best solution is to determine the voltage of your car battery using a multimeter. If it's below 11.5 volts then you must replace it. If the battery has corrosion it is essential to clean its contacts. This can be done by lifting the rubber covers covering both battery terminals and using wire brushes to clean any corroded areas of the battery. Then, you should reconnect the positive pole cables to the negative.
Water Damage
If your 208 isn't starting and the battery isn't flat then you should check whether the spark plugs are working. peugeot 207 replacement key could be that they're dirty, causing them to not to spark. The spark plugs can be cleaned in an workshop.
Peugeot automobiles use a key with a transponder that is compatible with the immobiliser. This makes sure that only the correct key can turn the engine. If the chip in the Peugeot key is damaged then it won't send the proper signal to the vehicle.
This is a very common issue that is caused by water damage. This is particularly prevalent in colder climates where the vehicle could have been exposed to rain or snow. In this situation, contact a reliable locksmith who will have the required tools and equipment to reprogram the key. They will also have all the latest technology and machinery required to make the Peugeot smart key. The process shouldn't take more than 15 minutes.
Contacts to the battery are not working properly.
Peugeot replaced the transponder chips with a new version that makes use of electronic components that are mounted on a circuitboard. The new system works great when it's new, however the circuit boards deteriorate over time and cease to function properly.
This could stop the immobiliser's function from being activated, meaning the vehicle won't start. Contact an Peugeot specialist or a locksmith, if this is the case.
The most frequent issue is when the battery inside the key fob starts to die. This causes the blade of the key to stop feeding into your lock. A locksmith in your car will replace the battery, and then cut a fresh blade for you. This is a quick fix.
Faulty Receiver Module
If your Peugeot key fob has stopped working after dropping it on the floor, being exposed to a sudden downpour or accidently washing it or washing it, it could be due to a faulty receiver module. The receiver is responsible for transmitting radio frequency signals to an on-board computer that controls the central locking system of your Peugeot vehicle.
The rubber seals on the key fob prevent water from getting to the electronic chip. The chip can be damaged by water when exposed to water for a long period of. The high salt content of the pool or ocean water could cause damage to the key fob if it is submerged.
If your Peugeot spare key fob stops working then you'll have to get the module replaced. This can only by done by an Peugeot specialist or a professional auto locksmith. Peugeot keys unlike other automobiles, are protected by an immobilizer system. This requires the correct codes to start the car. This is the reason why you should only be able to trust a professional Peugeot locksmith with the task of creating and programming a replacement.
Computer on board is not working properly
The on-board computer in your Peugeot is responsible for various features in your car, including airbags and power windows. If something is wrong with these systems, they will usually display a code indicating the issue. The code is stored within the system and will stay there until the issue is solved. This will often require the on-board computers to be replaced.
The most frequent cause for the warning light of the airbag to illuminate is corrosion or loose connections within the sensor. This could be due to wear and tear, aging or exposure to moisture and salt. It is crucial to get this issue addressed as soon as you can, as an airbag that is not functioning properly could be risky in the event of an accident.
If you find an error message stating that the card is not found on your Peugeot key fob, the battery inside the key fob might be dead or weak. This will stop the key fob sending a signal that will disable your vehicle's immobilizer. Test this by pressing the unlock button on the fob's key, then trying to start your car. If this does not work then the battery in the key fob is in need of replacement.